GIGA-PLUS-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY,
	OBJECT-TYPE,
	OBJECT-IDENTITY,
        IpAddress,
        Unsigned32,
        Counter64,
	NOTIFICATION-TYPE,
	enterprises,
	Opaque
		FROM SNMPv2-SMI
	MODULE-COMPLIANCE
		FROM SNMPv2-CONF
        DisplayString
                FROM SNMPv2-TC;
	
-- *******************************************************************
-- * Trango module
-- *******************************************************************
trango		OBJECT IDENTIFIER ::= { enterprises 5454 }
tbw 		OBJECT IDENTIFIER ::= { trango 1 }
ptp		OBJECT IDENTIFIER ::= { tbw 80 }

sys		OBJECT IDENTIFIER ::= { ptp 1 }
modem		OBJECT IDENTIFIER ::= { ptp 2 }
rf		OBJECT IDENTIFIER ::= { ptp 3 }
gige		OBJECT IDENTIFIER ::= { ptp 4 }
trangotrap	OBJECT IDENTIFIER ::= { ptp 6 }

-- *******************************************************************
-- ** System Information ** trango.tbw.ptp.sys
-- *******************************************************************

community       		OBJECT IDENTIFIER ::= { sys 8 }

sysSNMPReadCommStr  		OBJECT-TYPE
    	SYNTAX      		DisplayString (SIZE(1..32))
    	MAX-ACCESS  		read-write
    	STATUS      		current
    	DESCRIPTION 		"SNMP agent read community string"
    	::= { community 1 }

sysSNMPWriteCommStr 		OBJECT-TYPE
    	SYNTAX      		DisplayString (SIZE(1..32))
    	MAX-ACCESS  		read-write
    	STATUS      		current
    	DESCRIPTION 		"SNMP agent Write community string"
    	::= { community 2 }

sysTemperature              	OBJECT-TYPE
    	SYNTAX              	INTEGER
    	MAX-ACCESS          	read-only
    	STATUS              	current
    	DESCRIPTION         	"Current temperatur reading in Celsius"
    	::= { sys 19 }

sysVoltage                      OBJECT-TYPE
        SYNTAX                  Opaque
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display system voltage"
        ::= { sys 44 }

sysUptime                       OBJECT-TYPE
        SYNTAX                  DisplayString (SIZE(1..100))
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display system uptime"
        ::= { sys 45 }	

acm             		OBJECT IDENTIFIER ::= { modem 3  }

profile_x			OBJECT IDENTIFIER ::= { acm 5}

modemACMTxProfile		        OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ACM transmitter profile"
        ::= { profile_x 1 }

modemACMRxProfile            OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ACM receiver profile"
        ::= { profile_x 2 }

link             		OBJECT IDENTIFIER ::= { modem 4  }

link_ber				OBJECT IDENTIFIER ::= { link 1}

modemBER      			OBJECT-TYPE
        SYNTAX          	INTEGER
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display BER value"
        ::= { link_ber 1 }

modemBERStr     			OBJECT-TYPE
        SYNTAX          	DisplayString
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display BER value string"
        ::= { link_ber 2 }

link_mse             		OBJECT IDENTIFIER ::= { link 2  }

modemMSE      			OBJECT-TYPE
        SYNTAX          	INTEGER
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display MSE value"
        ::= { link_mse 1 }

modemMSEInt      		OBJECT-TYPE
        SYNTAX          	INTEGER
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display MSE value"
        ::= { link_mse 2 }

lock             		OBJECT IDENTIFIER ::= { modem 5  }

modemLockStatus      		OBJECT-TYPE
        SYNTAX          	INTEGER { nolock(0), lock(1), NA(2) }
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Set/Display link lock statsu"
        ::= { lock 1 }

debug             		OBJECT IDENTIFIER ::= { modem 6  }

modemLDPCStressDecoder      	OBJECT-TYPE
        SYNTAX          	INTEGER
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display LDPC Stress Decoder"
        ::= { debug 1 }

hc                              OBJECT IDENTIFIER ::= { modem 8  }

modemHCNetComp                  OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display HC net compression"
        ::= { hc 4 }

modemHCGrossComp                OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display HC gross compression"
        ::= { hc 5 }

modemTxCapacity                 OBJECT-TYPE
        SYNTAX                  Opaque
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display transmitter capacity (Float)"
        ::= { modem 10 }

modemSpeedCurrent               OBJECT-TYPE
        SYNTAX                  Opaque
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display current speed (Float)"
        ::= { modem 11 }

power             		OBJECT IDENTIFIER ::= { rf 4  }

rfPower      			OBJECT-TYPE
        SYNTAX          	Opaque
        MAX-ACCESS      	read-write
        STATUS          	current
        DESCRIPTION     	"Set/Display TX power.  SNMPc does not support
				setting and displaying float value."
        ::= { power 1 }

rfPowerInt      		OBJECT-TYPE
        SYNTAX          	INTEGER
        MAX-ACCESS      	read-write
        STATUS          	current
        DESCRIPTION     	"Set/Display TX power 1/10 dB in step size "
        ::= { power 2 }

rssi             		OBJECT IDENTIFIER ::= { rf 14  }

rfRSSIInt      			OBJECT-TYPE
    	SYNTAX              	INTEGER
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display current RSSI value  "
        ::= { rssi 2 }

pll             		OBJECT IDENTIFIER ::= { rf 15  }

rfTxpll      		OBJECT-TYPE
    	SYNTAX              	INTEGER { nolock(0), lock(1), na(2) }
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display current status of TX PLL  "
        ::= { pll 3 }

rfRxpll      		OBJECT-TYPE
    	SYNTAX              	INTEGER { nolock(0), lock(1), na(2) }
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display current status of RX PLL  "
        ::= { pll 4 }

eth1             		OBJECT IDENTIFIER ::= { gige 1  }

config1             		OBJECT IDENTIFIER ::= { eth1 1  }

gigeEth1Speed      		OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-write
        STATUS          	current
        DESCRIPTION     	"Set/Display speed setting for ETH 1"
        ::= { config1 7 }

gigeEth1Status      		OBJECT-TYPE
    	SYNTAX              	INTEGER { off(0), on(1) }
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Set/Display port status for ETH 1"
        ::= { config1 8 }

counter1             		OBJECT IDENTIFIER ::= { eth1 2  }

gigeEth1InTotalPackets      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 IN non-unicast packet counter"
        ::= { counter1 4 }

gigeEth1OutTotalPackets      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 OUT total packet counter"
        ::= { counter1 8 }

gigeEth1CRCError      		OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 CRC error counter"
        ::= { counter1 9 }

gigeEth1CollisionError      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 Collision error counter"
        ::= { counter1 10 }

gigeEth1InPortRate      	OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 In Port Rate"
        ::= { counter1 11 }

gigeEth1InPortUtil      	OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 In Port utilization"
        ::= { counter1 12 }

gigeEth1OutPortRate      	OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 Out Port Rate"
        ::= { counter1 13 }

gigeEth1OutPortUtil      	OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH1 Out Port utilization"
        ::= { counter1 14 }

gigeEth1InDiscard             OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display Eth1 In Discard"
        ::= { counter1 15 }

gigeEth1OutDiscard             OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display Eth1 Out Discard"
        ::= { counter1 16 }

eth2             		OBJECT IDENTIFIER ::= { gige 2  }

config2             		OBJECT IDENTIFIER ::= { eth2 1  }

gigeEth2Speed      		OBJECT-TYPE
        SYNTAX          	INTEGER 
        MAX-ACCESS      	read-write
        STATUS          	current
        DESCRIPTION     	"Set/Display speed setting for ETH 2"
        ::= { config2 7 }

gigeEth2Status      		OBJECT-TYPE
    	SYNTAX              	INTEGER { off(0), on(1) }
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Set/Display port status for ETH 2"
        ::= { config2 8 }

counter2             		OBJECT IDENTIFIER ::= { eth2 2  }

gigeEth2InTotalPackets      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH2 IN non-unicast packet counter"
        ::= { counter2 4 }

gigeEth2OutTotalPackets      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH2 OUT total packet counter"
        ::= { counter2 8 }

gigeEth2CRCError      		OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH2 CRC error counter"
        ::= { counter2 9 }

gigeEth2CollisionError      	OBJECT-TYPE
        SYNTAX          	Counter32 
        MAX-ACCESS      	read-only
        STATUS          	current
        DESCRIPTION     	"Display ETH2 Collision error counter"
        ::= { counter2 10 }

gigeEth2InPortRate              OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ETH2 In Port Rate"
        ::= { counter2 11 }

gigeEth2InPortUtil              OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ETH2 In Port utilization"
        ::= { counter2 12 }

gigeEth2OutPortRate             OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ETH2 Out Port Rate"
        ::= { counter2 13 }

gigeEth2OutPortUtil             OBJECT-TYPE
        SYNTAX                  INTEGER 
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display ETH2 Out Port utilization"
        ::= { counter2 14 }

gigeEth2InDiscard             OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display Eth2 In Discard"
        ::= { counter2 15 }

gigeEth2OutDiscard             OBJECT-TYPE
        SYNTAX                  INTEGER
        MAX-ACCESS              read-only
        STATUS                  current
        DESCRIPTION             "Display Eth2 Out Discard"
        ::= { counter2 16 }

END