GIGA-PLUS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, IpAddress, Unsigned32, Counter64, NOTIFICATION-TYPE, enterprises FROM SNMPv2-SMI MODULE-COMPLIANCE FROM SNMPv2-CONF DisplayString FROM SNMPv2-TC; -- ******************************************************************* -- * Trango module -- ******************************************************************* trango OBJECT IDENTIFIER ::= { enterprises 5454 } tbw OBJECT IDENTIFIER ::= { trango 1 } ptp OBJECT IDENTIFIER ::= { tbw 80 } sys OBJECT IDENTIFIER ::= { ptp 1 } modem OBJECT IDENTIFIER ::= { ptp 2 } rf OBJECT IDENTIFIER ::= { ptp 3 } gige OBJECT IDENTIFIER ::= { ptp 4 } tdm OBJECT IDENTIFIER ::= { ptp 5 } trangotrap OBJECT IDENTIFIER ::= { ptp 6 } -- ******************************************************************* -- ** System Information ** trango.tbw.ptp.sys -- ******************************************************************* ver OBJECT IDENTIFIER ::= { sys 1 } sysFPGAVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "FPGA 1 Version" ::= { ver 1 } sysOSVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU OS Version" ::= { ver 2 } sysFWVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU FW Version" ::= { ver 3 } sysPICVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU PIC Version" ::= { ver 4 } sysModemVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU Modem Version" ::= { ver 5 } sysODUFWVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "ODU 1 FW Version" ::= { ver 6 } prever OBJECT IDENTIFIER ::= { sys 2 } sysFPGAPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "FPGA 1 PreVersion" ::= { prever 1 } sysOSPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU OS PreVersion" ::= { prever 2 } sysFWPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU FW PreVersion" ::= { prever 3 } sysPICPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU PIC PreVersion" ::= { prever 4 } sysModemPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU Modem PreVersion" ::= { prever 5 } sysODUFWPreVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "ODU 1 FW PreVersion" ::= { prever 6 } model OBJECT IDENTIFIER ::= { sys 3 } sysIDUModel OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU Model" ::= { model 1 } sysODUModel OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "ODU 1 model" ::= { model 2 } sysIDUSerialID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "IDU Serial ID" ::= { model 3 } sysODUSerialID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "ODU 1 Serial ID" ::= { model 4 } sysOMUProjectID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "ODU Project ID" ::= { model 5 } mac OBJECT IDENTIFIER ::= { sys 4 } sysMACeth1 OBJECT-TYPE SYNTAX DisplayString (SIZE(12)) MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of Ethernet 1" ::= { mac 1 } ipconfig OBJECT IDENTIFIER ::= { sys 5 } sysIpAddressess OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address" ::= { ipconfig 1 } sysSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask" ::= { ipconfig 2 } sysDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Default gateway" ::= { ipconfig 3 } sysRemarkSystem OBJECT-TYPE SYNTAX DisplayString (SIZE(1..100)) MAX-ACCESS read-write STATUS current DESCRIPTION "System remarks" ::= { sys 6 } ibm OBJECT IDENTIFIER ::= { sys 7 } sysIBMEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Inband Management feature" ::= { ibm 1 } sysIBMVlanID OBJECT-TYPE SYNTAX INTEGER {0 - 4090} MAX-ACCESS read-write STATUS current DESCRIPTION "IBM Vlan ID" ::= { ibm 4 } sysIBMDataPort OBJECT-TYPE SYNTAX INTEGER { GE1(1), GE2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IBM/Data Port" ::= { ibm 5 } sysIBMTagging OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Inband Management tagging feature" ::= { ibm 6 } sysRemoteManagement OBJECT-TYPE SYNTAX INTEGER { Off(0), On(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Remote management through out of band" ::= { ibm 7 } community OBJECT IDENTIFIER ::= { sys 8 } sysSNMPReadCommStr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP agent read community string" ::= { community 1 } sysSNMPWriteCommStr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP agent Write community string" ::= { community 2 } sysSNMPTrapCommStr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP trap community string" ::= { community 3 } sysIDUTemp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "PIC's current temperatur reading in Celsius" ::= { sys 19 } daemon OBJECT IDENTIFIER ::= { sys 20 } sysHTTPD OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable HTTPD" ::= { daemon 1 } sysSNMPD OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable SNMPD" ::= { daemon 2 } sysTFTPD OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TFPTD" ::= { daemon 3 } sysTelnetd OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Telnetd" ::= { daemon 4 } sysClearCounter OBJECT-TYPE SYNTAX INTEGER { na(0), clear(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear data port counters" ::= { sys 22 } remote OBJECT IDENTIFIER ::= { sys 33 } sysRemoteLinkStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display remote link status" ::= { remote 1 } sysRemoteLinkODUStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display remote ODU status" ::= { remote 2 } rssi_remote OBJECT IDENTIFIER ::= { remote 3 } sysRemoteLinkRSSI OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display remote RSSI" ::= { rssi_remote 1 } mse_remote OBJECT IDENTIFIER ::= { remote 4 } sysRemoteLinkMSE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display remote MSE" ::= { mse_remote 1 } sysRemoteLinkRx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display remote Rx status" ::= { remote 5 } threshold OBJECT IDENTIFIER ::= { sys 34 } th_rssi OBJECT IDENTIFIER ::= { threshold 1 } sysThresholdRSSIMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum threshold RSSI" ::= { th_rssi 1 } sysThresholdRSSIMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum threshold RSSI" ::= { th_rssi 2 } sysThresholdRSSIAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold RSSI action" ::= { th_rssi 3 } th_mse OBJECT IDENTIFIER ::= { threshold 2 } sysThresholdMSEMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum threshold MSE" ::= { th_mse 1 } sysThresholdMSEMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum threshold MSE" ::= { th_mse 2 } sysThresholdMSEAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold MSE action" ::= { th_mse 3 } th_ber OBJECT IDENTIFIER ::= { threshold 3 } sysThresholdBERMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum threshold BER" ::= { th_ber 1 } sysThresholdBERMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum threshold BER" ::= { th_ber 2 } sysThresholdBERAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold BER action" ::= { th_ber 3 } th_idu_temp OBJECT IDENTIFIER ::= { threshold 5 } sysThresholdIDUTempMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum IDU temp" ::= { th_idu_temp 1 } sysThresholdIDUTempMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum IDU temp" ::= { th_idu_temp 2 } sysThresholdIDUTempAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold IDU temp" ::= { th_idu_temp 3 } th_odu_temp OBJECT IDENTIFIER ::= { threshold 6 } sysThresholdODUTempMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum ODU temp" ::= { th_odu_temp 1 } sysThresholdODUTempMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum ODU temp" ::= { th_odu_temp 2 } sysThresholdODUTempAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold ODU temp" ::= { th_odu_temp 3 } th_in_port OBJECT IDENTIFIER ::= { threshold 7 } sysThresholdInPortUtilMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum In port util" ::= { th_in_port 1 } sysThresholdInPortUtilMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum In port util" ::= { th_in_port 2 } sysThresholdInPortUtilAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold In port util action" ::= { th_in_port 3 } th_out_port OBJECT IDENTIFIER ::= { threshold 8 } sysThresholdOutPortUtilMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure minimum Out port util" ::= { th_out_port 1 } sysThresholdOutPortUtilMax OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure maximum Out port util" ::= { th_out_port 2 } sysThresholdOutPortUtilAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold Out port util action" ::= { th_out_port 3 } th_link_down OBJECT IDENTIFIER ::= { threshold 9 } sysThresholdLinkDownAction OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure threshold link down action" ::= { th_link_down 1 } sysEgressMargin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure Ethernet Egress margin" ::= { sys 35 } sysQOSMode OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure QOS Mode" ::= { sys 36 } sysSpeedLicense OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure speed license" ::= { sys 39 } gps OBJECT IDENTIFIER ::= { sys 43 } sysGPSFirst OBJECT-TYPE SYNTAX DisplayString (SIZE(1..100)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure gps coordinate 1" ::= { gps 1 } sysGPSSecond OBJECT-TYPE SYNTAX DisplayString (SIZE(1..100)) MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure gps coordinate 2" ::= { gps 2 } sysVoltage OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display system voltage" ::= { sys 44 } sysUptime OBJECT-TYPE SYNTAX DisplayString (SIZE(1..100)) MAX-ACCESS read-only STATUS current DESCRIPTION "Display system uptime" ::= { sys 45 } sysVoltage12 OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display power input(1.2V) " ::= { sys 49 } sysVoltage25 OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display power input(2.5V)" ::= { sys 50 } sysVoltage33 OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display power input(3.3V)" ::= { sys 51 } loopback OBJECT IDENTIFIER ::= { modem 1} modemLoopbackMode OBJECT-TYPE SYNTAX INTEGER { off(0), digital(1), if(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display the Loopback Mode" ::= { loopback 1 } modemLoopbackAuto OBJECT-TYPE SYNTAX INTEGER { 1(Run loopback auto) } MAX-ACCESS read-write STATUS current DESCRIPTION "Run loopback auto" ::= { loopback 2 } acm OBJECT IDENTIFIER ::= { modem 3 } improve OBJECT IDENTIFIER ::= { acm 3 } qpsk_improve OBJECT IDENTIFIER ::= { improve 1 } modemACMQPSKMSEImporve OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for QPSK" ::= { qpsk_improve 1 } modemACMQPSKMSEImporveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for QPSK in INTEGER" ::= { qpsk_improve 2 } qam16_improve OBJECT IDENTIFIER ::= { improve 2 } modemACM16QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 16Q" ::= { qam16_improve 1 } modemACM16QMSEImproveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 16Q in INTEGER" ::= { qam16_improve 2 } qam32_improve OBJECT IDENTIFIER ::= { improve 3 } modemACM32QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 32Q" ::= { qam32_improve 1 } modemACM32QMSEImproveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 32Q INTEGER" ::= { qam32_improve 2 } qam64_improve OBJECT IDENTIFIER ::= { improve 4 } modemACM64QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 64Q" ::= { qam64_improve 1 } modemACM64QMSEImproveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 64Q in INTEGER" ::= { qam64_improve 2 } qam128_improve OBJECT IDENTIFIER ::= { improve 5 } modemACM128QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 128Q" ::= { qam128_improve 1 } modemACM128QMSEImproveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 128Q in INTEGER" ::= { qam128_improve 2 } qam256_improve OBJECT IDENTIFIER ::= { improve 6 } modemACM256QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 256Q" ::= { qam256_improve 1 } modemACM256QMSEImproveInt OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 256Q in INTEGER" ::= { qam256_improve 2 } qam512_improve OBJECT IDENTIFIER ::= { improve 7 } modemACM512QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 512Q" ::= { qam512_improve 1 } modemACM512QMSEImproveInt OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 512Q in INTEGER" ::= { qam512_improve 2 } qam1024_improve OBJECT IDENTIFIER ::= { improve 8 } modemACM1024QMSEImprove OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 1024Q" ::= { qam1024_improve 1 } modemACM1024QMSEImproveInt OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 1024Q in INTEGER" ::= { qam1024_improve 2 } q8psk_improve OBJECT IDENTIFIER ::= { improve 9 } modemACM8PSKMSEImporve OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 8PSK" ::= { q8psk_improve 1 } modemACM8PSKMSEImporveInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE improve value for 8PSK in INTEGER" ::= { q8psk_improve 2 } degrade OBJECT IDENTIFIER ::= { acm 4 } qpsk_degrade OBJECT IDENTIFIER ::= { degrade 1 } modemACMQPSKMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for QPSK" ::= { qpsk_degrade 1 } modemACMQPSKMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for QPSK in INTEGER" ::= { qpsk_degrade 2 } qam16_degrade OBJECT IDENTIFIER ::= { degrade 2 } modemACM16QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 16Q" ::= { qam16_degrade 1 } modemACM16QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 16Q in INTEGER" ::= { qam16_degrade 2 } qam32_degrade OBJECT IDENTIFIER ::= { degrade 3 } modemACM32QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 32Q" ::= { qam32_degrade 1 } modemACM32QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 32Q in INTEGER" ::= { qam32_degrade 2 } qam64_degrade OBJECT IDENTIFIER ::= { degrade 4 } modemACM64QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 64Q" ::= { qam64_degrade 1 } modemACM64QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 64Q in INTEGER" ::= { qam64_degrade 2 } qam128_degrade OBJECT IDENTIFIER ::= { degrade 5 } modemACM128QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 128Q" ::= { qam128_degrade 1 } modemACM128QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 128Q in INTEGER" ::= { qam128_degrade 2 } qam256_degrade OBJECT IDENTIFIER ::= { degrade 6 } modemACM256QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 256Q" ::= { qam256_degrade 1 } modemACM256QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 256Q in INTEGER" ::= { qam256_degrade 2 } qam512_degrade OBJECT IDENTIFIER ::= { degrade 7 } modemACM512QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 512Q" ::= { qam512_degrade 1 } modemACM512QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 512Q in INTEGER" ::= { qam512_degrade 2 } qam1024_degrade OBJECT IDENTIFIER ::= { degrade 8 } modemACM1024QMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 1024Q" ::= { qam1024_degrade 1 } modemACM1024QMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 1024Q in INTEGER" ::= { qam1024_degrade 2 } q8psk_degrade OBJECT IDENTIFIER ::= { degrade 9 } modemACM8PSKMSEDegrade OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 8PSK" ::= { q8psk_degrade 1 } modemACM8PSKMSEDegradeInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display ACM MSE degrade value for 8PSK in INTEGER" ::= { q8psk_degrade 2 } profile_x OBJECT IDENTIFIER ::= { acm 5} modemACMTxProfile OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display ACM transmitter profile" ::= { profile_x 1 } modemACM256RxProfile OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display ACM receiver profile" ::= { profile_x 2 } link OBJECT IDENTIFIER ::= { modem 4 } link_ber OBJECT IDENTIFIER ::= { link 1 } modemBER OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display BER value" ::= { link_ber 1 } modemBERStr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Display BER value string" ::= { link_ber 2 } mse OBJECT IDENTIFIER ::= { link 2 } modemMSE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display MSE value" ::= { mse 1 } modemMSEInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display MSE value" ::= { mse 2 } lock OBJECT IDENTIFIER ::= { modem 5 } modemLockStatus OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display link lock statsu" ::= { lock 1 } modemTimingLockStatus OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display timing lock statsu" ::= { lock 2 } modemPreambleLockStatus OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display preamble lock statsu" ::= { lock 3 } modemLDPCLocktatus OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1) , NA(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display LDPC lock statsu" ::= { lock 4 } debug OBJECT IDENTIFIER ::= { modem 6 } modemLDPCStressDecoder OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display LDPC Stress Decoder" ::= { debug 1 } modemRadioMSE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio MSE" ::= { debug 3 } hc OBJECT IDENTIFIER ::= { modem 8 } modemHCEnable OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure header compression enable option" ::= { hc 1 } modemHCEng1Num OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display HC engine 1 flow number" ::= { hc 2 } modemHCEng2Num OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display HC engine 2 flow number" ::= { hc 3 } modemHCNetComp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display HC net compression" ::= { hc 4 } modemHCGrossComp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display HC gross compression" ::= { hc 5 } modemXPICEnable OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure xpic enable option" ::= { modem 9 } modemTxCapacity OBJECT-TYPE SYNTAX OPAQUE(Float) MAX-ACCESS read-only STATUS current DESCRIPTION "Display transmitter capacity" ::= { modem 10 } modemSpeedCurrent OBJECT-TYPE SYNTAX OPAQUE(Float) MAX-ACCESS read-only STATUS current DESCRIPTION "Display current speed" ::= { modem 11 } freq OBJECT IDENTIFIER ::= { rf 1 } txfreq OBJECT IDENTIFIER ::= { freq 1 } rfTxFrequency OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display TX frequency" ::= { txfreq 1 } rfTxFrequencyInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display TX frequency in integer value" ::= { txfreq 2 } rxfreq OBJECT IDENTIFIER ::= { freq 2 } rfRxFrequency OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display RX frequency" ::= { rxfreq 1 } rfRxFrequencyInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RX frequency in integer value" ::= { rxfreq 2 } duplex OBJECT IDENTIFIER ::= { freq 3 } rfFreqDuplex OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Display frequency duplex" ::= { duplex 1 } rfFreqDuplexInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display frequency duplex in integer value" ::= { duplex 2 } freqmax OBJECT IDENTIFIER ::= { freq 4 } rfFreqMax OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display maximum TX frequency" ::= { freqmax 1 } rfFreqMaxInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display maximum TX frequency in integer value" ::= { freqmax 2 } freqmin OBJECT IDENTIFIER ::= { freq 5 } rfFreqMin OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display minimum TX frequency" ::= { freqmin 1 } rfFreqMinInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display minimum TX frequency in integer value" ::= { freqmin 2 } rfOpmode OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display current opmode setting " ::= { rf 3 } power OBJECT IDENTIFIER ::= { rf 4 } rfPower OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display TX power. SNMPc does not support setting and displaying float value." ::= { power 1 } rfPowerInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display TX power 1/10 dB in step size " ::= { power 2 } speed OBJECT IDENTIFIER ::= { rf 6 } chwidth OBJECT IDENTIFIER ::= { speed 1 } rfChannelWidth OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display Speed channel width " ::= { chwidth 1 } rfmod OBJECT IDENTIFIER ::= {speed 2} rfModulationMin OBJECT-TYPE SYNTAX INTEGER { qpsk(0), 8psk(1), qam16(2), qam32(3), qam64(4), qam128(5), qam256(6), qam512(7), qam1024(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display minimum speed modulation " ::= { rfmod 1 } rfModulationMax OBJECT-TYPE SYNTAX INTEGER { qpsk(0), 8psk(1), qam16(2), qam32(3), qam64(4), qam128(5), qam256(6), qam512(7), qam1024(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display maximum speed modulation " ::= { rfmod 2 } symrate OBJECT IDENTIFIER ::= { speed 3 } rfSymrate OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display Speed symbol rate " ::= { symrate 1 } rfSymrateInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Speed symbol rate in INTEGER " ::= { symrate 2 } sp OBJECT IDENTIFIER ::= { speed 4 } rfSpeed OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display Speed rate " ::= { sp 1 } rfSpeedInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Speed rate in INTEGER " ::= { sp 2 } rfSpeedSmall OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display small packet capacity " ::= { sp 3 } rfSpeedSmallInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display small packet capacity in INTEGER " ::= { sp 4 } rfSetSpeedL OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display set speed large packet capacity " ::= { sp 5 } rfSetSpeedS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display set speed small packet capacity " ::= { sp 6 } rfRxSpeedL OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display Rx speed large packet capacity " ::= { sp 7 } rfRxSpeedS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Rx speed small packet capacity " ::= { sp 8 } rfODUPowerEnable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display current status of ODU power " ::= { rf 11 } rfODUTemp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display current ODU temperature " ::= { rf 13 } rssi OBJECT IDENTIFIER ::= { rf 14 } rfRSSI OBJECT-TYPE SYNTAX Opaque MAX-ACCESS read-only STATUS current DESCRIPTION "Display current RSSI value in float " ::= { rssi 1 } rfRSSIInt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display current RSSI value " ::= { rssi 2 } pll OBJECT IDENTIFIER ::= { rf 15 } rfODUIFpll OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Display current status of ODU IF PLL " ::= { pll 2 } rfODUTxpll OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Display current status of ODU TX PLL " ::= { pll 3 } rfODURxpll OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Display current status of ODU RX PLL " ::= { pll 4 } rfIDUTxpll OBJECT-TYPE SYNTAX INTEGER { nolock(0), lock(1), NA(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Display current status of IDU TX PLL " ::= { pll 5 } incounter OBJECT IDENTIFIER ::= { rf 16 } rfInDataOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF IN data octets counter " ::= { incounter 1 } rfInDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF IN data packets counter " ::= { incounter 2 } rfInDataDropPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF IN data drop packets counter " ::= { incounter 3 } rfInPortRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF IN port rate " ::= { incounter 4 } rfInPortUtil OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF IN port utilization " ::= { incounter 5 } outcounter OBJECT IDENTIFIER ::= { rf 17 } rfOutDataOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF OUT data octets counter " ::= { outcounter 1 } rfOutDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF OUT data packets counter " ::= { outcounter 2 } rfOutPortRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF OUT port rate " ::= { outcounter 3 } rfOutPortUtil OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF OUT port utilization " ::= { outcounter 4 } rfOMUTemp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF OUT port utilization " ::= { rf 19 } eth1 OBJECT IDENTIFIER ::= { gige 1 } config1 OBJECT IDENTIFIER ::= { eth1 1 } gigeEth1AutNegotiate OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display auto neogitate setting for ETH 1" ::= { config1 1 } gigeEth1Duplex OBJECT-TYPE SYNTAX INTEGER { half(0), full(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display duplex setting for ETH 1" ::= { config1 2 } gigeEth1Enable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display enable setting for ETH 1" ::= { config1 3 } gigeEth1MaxRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display max rate setting for ETH 1" ::= { config1 4 } gigeEth1PauseFrame OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display pause frame setting for ETH 1" ::= { config1 5 } gigeEth1Priority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display priority setting for ETH 1" ::= { config1 6 } gigeEth1Speed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display speed setting for ETH 1" ::= { config1 7 } gigeEth1Status OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display port status for ETH 1" ::= { config1 8 } counter1 OBJECT IDENTIFIER ::= { eth1 2 } gigeEth1InOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 IN octets counter" ::= { counter1 1 } gigeEth1InUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 IN unicast packet counter" ::= { counter1 2 } gigeEth1InNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 IN non-unicast packet counter" ::= { counter1 3 } gigeEth1InTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 IN non-unicast packet counter" ::= { counter1 4 } gigeEth1OutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 OUT octets counter" ::= { counter1 5 } gigeEth1OutUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 OUT unicast packet counter" ::= { counter1 6 } gigeEth1OutNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 OUT non-unicast packet counter" ::= { counter1 7 } gigeEth1OutTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 OUT total packet counter" ::= { counter1 8 } gigeEth1CRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 CRC error counter" ::= { counter1 9 } gigeEth1CollisionError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 Collision error counter" ::= { counter1 10 } gigeEth1InPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 In Port Rate" ::= { counter1 11 } gigeEth1InPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 In Port utilization" ::= { counter1 12 } gigeEth1OutPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 Out Port Rate" ::= { counter1 13 } gigeEth1OutPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH1 Out Port utilization" ::= { counter1 14 } gigeEth1InDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 In Discard" ::= { counter1 15 } gigeEth1OutDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 Out Discard" ::= { counter1 16 } gigeEth1InPkt64 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt64" ::= { counter1 17 } gigeEth1InPkt64_127 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt64_127" ::= { counter1 18 } gigeEth1InPkt128_255 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt128_255" ::= { counter1 19 } gigeEth1InPkt256_511 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt256_511" ::= { counter1 20 } gigeEth1InPkt512_1023 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt512_1023" ::= { counter1 21 } gigeEth1InPkt1024_1518 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt1024_1518" ::= { counter1 22 } gigeEth1InPkt1519over OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth1 InPkt1519over" ::= { counter1 23 } eth2 OBJECT IDENTIFIER ::= { gige 2 } config2 OBJECT IDENTIFIER ::= { eth2 1 } gigeEth2AutNegotiate OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display auto neogitate setting for ETH 2" ::= { config2 1 } gigeEth2Duplex OBJECT-TYPE SYNTAX INTEGER { half(0), full(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display duplex setting for ETH 2" ::= { config2 2 } gigeEth2Enable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display enable setting for ETH 2" ::= { config2 3 } gigeEth2MaxRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display max rate setting for ETH 2" ::= { config2 4 } gigeEth2PauseFrame OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display pause frame setting for ETH 2" ::= { config2 5 } gigeEth2Priority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display priority setting for ETH 2" ::= { config2 6 } gigeEth2Speed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display speed setting for ETH 2" ::= { config2 7 } gigeEth2Status OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display port status for ETH 2" ::= { config2 8 } counter2 OBJECT IDENTIFIER ::= { eth2 2 } gigeEth2InOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 IN octets counter" ::= { counter2 1 } gigeEth2InUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 IN unicast packet counter" ::= { counter2 2 } gigeEth2InNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 IN non-unicast packet counter" ::= { counter2 3 } gigeEth2InTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 IN non-unicast packet counter" ::= { counter2 4 } gigeEth2OutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 OUT octets counter" ::= { counter2 5 } gigeEth2OutUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 OUT unicast packet counter" ::= { counter2 6 } gigeEth2OutNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 OUT non-unicast packet counter" ::= { counter2 7 } gigeEth2OutTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 OUT total packet counter" ::= { counter2 8 } gigeEth2CRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 CRC error counter" ::= { counter2 9 } gigeEth2CollisionError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 Collision error counter" ::= { counter2 10 } gigeEth2InPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 In Port Rate" ::= { counter2 11 } gigeEth2InPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 In Port utilization" ::= { counter2 12 } gigeEth2OutPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 Out Port Rate" ::= { counter2 13 } gigeEth2OutPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display ETH2 Out Port utilization" ::= { counter2 14 } gigeEth2InDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 In Discard" ::= { counter2 15 } gigeEth2OutDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 Out Discard" ::= { counter2 16 } gigeEth2InPkt64 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt64" ::= { counter2 17 } gigeEth2InPkt64_127 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt64_127" ::= { counter2 18 } gigeEth2InPkt128_255 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt128_255" ::= { counter2 19 } gigeEth2InPkt256_511 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt256_511" ::= { counter2 20 } gigeEth2InPkt512_1023 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt512_1023" ::= { counter2 21 } gigeEth2InPkt1024_1518 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt1024_1518" ::= { counter2 22 } gigeEth2InPkt1519over OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth2 InPkt1519over" ::= { counter2 23 } eth3 OBJECT IDENTIFIER ::= { gige 3 } config3 OBJECT IDENTIFIER ::= { eth3 1 } gigeEth3AutNegotiate OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display auto neogitate setting for ETH 3" ::= { config3 1 } gigeEth3Duplex OBJECT-TYPE SYNTAX INTEGER { half(0), full(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display duplex setting for ETH 3" ::= { config3 2 } gigeEth3Enable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display enable setting for ETH 3" ::= { config3 3 } gigeEth3MaxRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display max rate setting for ETH 3" ::= { config3 4 } gigeEth3PauseFrame OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display pause frame setting for ETH 3" ::= { config3 5 } gigeEth3Priority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display priority setting for ETH 3" ::= { config3 6 } gigeEth3Speed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display speed setting for ETH 3" ::= { config3 7 } gigeEth3Status OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display port status for ETH 3" ::= { config3 8 } counter3 OBJECT IDENTIFIER ::= { eth3 2 } gigeEth3InOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 IN octets counter" ::= { counter3 1 } gigeEth3InUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 IN unicast packet counter" ::= { counter3 2 } gigeEth3InNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 IN non-unicast packet counter" ::= { counter3 3 } gigeEth3InTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 IN non-unicast packet counter" ::= { counter3 4 } gigeEth3OutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 OUT octets counter" ::= { counter3 5 } gigeEth3OutUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 OUT unicast packet counter" ::= { counter3 6 } gigeEth3OutNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 OUT non-unicast packet counter" ::= { counter3 7 } gigeEth3OutTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 OUT total packet counter" ::= { counter3 8 } gigeEth3CRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 CRC error counter" ::= { counter3 9 } gigeEth3CollisionError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 Collision error counter" ::= { counter3 10 } gigeEth3InPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 In Port Rate" ::= { counter3 11 } gigeEth3InPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 In Port utilization" ::= { counter3 12 } gigeEth3OutPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 Out Port Rate" ::= { counter3 13 } gigeEth3OutPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 Out Port utilization" ::= { counter3 14 } gigeEth3InDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 In Discard" ::= { counter3 15 } gigeEth3OutDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 Out Discard" ::= { counter3 16 } gigeEth3InPkt64 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt64" ::= { counter3 17 } gigeEth3InPkt64_127 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt64_127" ::= { counter3 18 } gigeEth3InPkt128_255 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt128_255" ::= { counter3 19 } gigeEth3InPkt256_511 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt256_511" ::= { counter3 20 } gigeEth3InPkt512_1023 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt512_1023" ::= { counter3 21 } gigeEth3InPkt1024_1518 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt1024_1518" ::= { counter3 22 } gigeEth3InPkt1519over OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth3 InPkt1519over" ::= { counter3 23 } eth4 OBJECT IDENTIFIER ::= { gige 4 } config4 OBJECT IDENTIFIER ::= { eth4 1 } gigeEth4AutNegotiate OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display auto neogitate setting for ETH 4" ::= { config4 1 } gigeEth4Duplex OBJECT-TYPE SYNTAX INTEGER { half(0), full(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display duplex setting for ETH 4" ::= { config4 2 } gigeEth4Enable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display enable setting for ETH 4" ::= { config4 3 } gigeEth4MaxRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display max rate setting for ETH 4" ::= { config4 4 } gigeEth4PauseFrame OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display pause frame setting for ETH 4" ::= { config4 5 } gigeEth4Priority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display priority setting for ETH 4" ::= { config4 6 } gigeEth4Speed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display speed setting for ETH 4" ::= { config4 7 } gigeEth4Status OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display port status for ETH 4" ::= { config4 8 } counter4 OBJECT IDENTIFIER ::= { eth4 2 } gigeEth4InOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 IN octets counter" ::= { counter4 1 } gigeEth4InUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 IN unicast packet counter" ::= { counter4 2 } gigeEth4InNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 IN non-unicast packet counter" ::= { counter4 3 } gigeEth4InTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 IN non-unicast packet counter" ::= { counter4 4 } gigeEth4OutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 OUT octets counter" ::= { counter4 5 } gigeEth4OutUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 OUT unicast packet counter" ::= { counter4 6 } gigeEth4OutNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 OUT non-unicast packet counter" ::= { counter4 7 } gigeEth4OutTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 OUT total packet counter" ::= { counter4 8 } gigeEth4CRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 CRC error counter" ::= { counter4 9 } gigeEth4CollisionError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 Collision error counter" ::= { counter4 10 } gigeEth4InPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 In Port Rate" ::= { counter4 11 } gigeEth4InPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 In Port utilization" ::= { counter4 12 } gigeEth4OutPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 Out Port Rate" ::= { counter4 13 } gigeEth4OutPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 Out Port utilization" ::= { counter4 14 } gigeEth4InDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 In Discard" ::= { counter4 15 } gigeEth4OutDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 Out Discard" ::= { counter4 16 } gigeEth4InPkt64 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt64" ::= { counter4 17 } gigeEth4InPkt64_127 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt64_127" ::= { counter4 18 } gigeEth4InPkt128_255 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt128_255" ::= { counter4 19 } gigeEth4InPkt256_511 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt256_511" ::= { counter4 20 } gigeEth4InPkt512_1023 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt512_1023" ::= { counter4 21 } gigeEth4InPkt1024_1518 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt1024_1518" ::= { counter4 22 } gigeEth4InPkt1519over OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Eth4 InPkt1519over" ::= { counter4 23 } PLAStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display pla status" ::= { gige 7 } PLAEnable OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Display/Configure pla enable option" ::= { gige 8 } radio OBJECT IDENTIFIER ::= { gige 9 } modemconfig OBJECT IDENTIFIER ::= { radio 1 } gigeModemAutNegotiate OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display auto neogitate setting for radio" ::= { modemconfig 1 } gigeModemDuplex OBJECT-TYPE SYNTAX INTEGER { half(0), full(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display duplex setting for radio" ::= { modemconfig 2 } gigeModemEnable OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display enable setting for radio" ::= { modemconfig 3 } gigeModemMaxRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display max rate setting for radio" ::= { modemconfig 4 } gigeModemPauseFrame OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display pause frame setting for radio" ::= { modemconfig 5 } gigeModemPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display priority setting for radio" ::= { modemconfig 6 } gigeModemSpeed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display speed setting for radio" ::= { modemconfig 7 } gigeModemStatus OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set/Display port status for radio" ::= { modemconfig 8 } modemcounter OBJECT IDENTIFIER ::= { radio 2 } gigeModemInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio IN octets counter" ::= { modemcounter 1 } gigeModemInUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio IN unicast packet counter" ::= { modemcounter 2 } gigeModemInNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio IN non-unicast packet counter" ::= { modemcounter 3 } gigeModemInTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio IN non-unicast packet counter" ::= { modemcounter 4 } gigeModemOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio OUT octets counter" ::= { modemcounter 5 } gigeModemOutUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio OUT unicast packet counter" ::= { modemcounter 6 } gigeModemOutNUcastPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio OUT non-unicast packet counter" ::= { modemcounter 7 } gigeModemOutTotalPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio OUT total packet counter" ::= { modemcounter 8 } gigeModemCRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio CRC error counter" ::= { modemcounter 9 } gigeModemCollisionError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio Collision error counter" ::= { modemcounter 10 } gigeModemInPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio In Port Rate" ::= { modemcounter 11 } gigeModemInPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio In Port utilization" ::= { modemcounter 12 } gigeModemOutPortRate OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio Out Port Rate" ::= { modemcounter 13 } gigeModemOutPortUtil OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio Out Port utilization" ::= { modemcounter 14 } gigeModemInDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio In Discard" ::= { modemcounter 15 } gigeModemOutDiscard OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio Out Discard" ::= { modemcounter 16 } gigeModemInPkt64 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt64" ::= { modemcounter 17 } gigeModemInPkt64_127 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt64_127" ::= { modemcounter 18 } gigeModemInPkt128_255 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt128_255" ::= { modemcounter 19 } gigeModemInPkt256_511 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt256_511" ::= { modemcounter 20 } gigeModemInPkt512_1023 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt512_1023" ::= { modemcounter 21 } gigeModemInPkt1024_1518 OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt1024_1518" ::= { modemcounter 22 } gigeModemInPkt1519over OBJECT-TYPE SYNTAX Integer MAX-ACCESS read-only STATUS current DESCRIPTION "Display Radio InPkt1519over" ::= { modemcounter 23 } gigeSynceSource OBJECT-TYPE SYNTAX Integer { Copper(0), Fiber(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display Synce source" ::= { gige 10 } gigeSynceMode OBJECT-TYPE SYNTAX Integer { Off(0), Master(1), Slave(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Display Synce mode" ::= { gige 11 } trapStartUp NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the system starts up" ::= { trangotrap 1 } reset OBJECT IDENTIFIER ::= { trangotrap 2 } trapReboot NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the system reboots" ::= { reset 1 } trapIPReset NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the IP resets" ::= { reset 2 } trapConfigReset NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the config is reset" ::= { reset 3 } traprps OBJECT IDENTIFIER ::= { trangotrap 3 } trapRPSPortUp NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the rapid port up occurs" ::= { traprps 1 } trapRPSPortDown NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the rapid port down occurs" ::= { traprps 2 } trapeth OBJECT IDENTIFIER ::= { trangotrap 4 } trapEth1StatusUpdate NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when ethernet port 1 status changed" ::= { trapeth 1 } trapEth2StatusUpdate NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when ethernet port 2 status changed" ::= { trapeth 2 } acm_profile OBJECT IDENTIFIER ::= { trangotrap 5 } trapLinkLock NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the system lose modem lock" ::= { acm_profile 1 } trapACMTxProfileChange NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the ACM Tx profile changes" ::= { acm_profile 2 } trapACMRxProfileChange NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the ACM Rx profile changes" ::= { acm_profile 3 } trap_threshold OBJECT IDENTIFIER ::= { trangotrap 6 } trapIDUTempMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the IDU temp below min" ::= { trap_threshold 1 } trapIDUTempMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the IDU temp above max" ::= { trap_threshold 2 } trapODUTempMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the ODU temp below min" ::= { trap_threshold 3 } trapODUTempMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the ODU temp above max" ::= { trap_threshold 4 } trapMSEMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the MSE below min" ::= { trap_threshold 5 } trapMSEMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the MSE above max" ::= { trap_threshold 6 } trapBERMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the BER below min" ::= { trap_threshold 7 } trapBERMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the BER above max" ::= { trap_threshold 8 } trapFERMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the FER below min" ::= { trap_threshold 9 } trapFERMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the FER above max" ::= { trap_threshold 10 } trapRSSIMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the RSSI below min" ::= { trap_threshold 11 } trapRSSIMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when the RSSI above max" ::= { trap_threshold 12 } trapInPortUtilMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when IN port utilization below min" ::= { trap_threshold 13 } trapInPortUtilMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when IN port utilization above max" ::= { trap_threshold 14 } trapOutPortUtilMin NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when OUT port utilization below min" ::= { trap_threshold 15 } trapOutPortUtilMax NOTIFICATION-TYPE STATUS current DESCRIPTION "send traps when OUT port utilization above max" ::= { trap_threshold 16 } END